2 voti

B-WAX RELEASE - High quality brush release agent, prevents adhesion between silicone rubbers and resins

Product not available


B-Wax Release (1 l) is for Epoxy, Polyurethane, and Acrylic Resins and Silicone rubber
A wax-based product for application with brush  for molds and models in which to pour resin.

VAT included
Your price list -20%
VAT included
Lowest price within 30 days before promotion. €14.53
Time left

Are you looking for larger formats? Visit the large quantities section or
Receive an alert when the product will be available
Warning cart
Safety information
+ -

In accordance with Regulation nº1272/2008 (CLP), the product is classified as hazardous

Section A

Hazard statements:

  • Aquatic Chronic 2: H411 - Toxic to aquatic life with long lasting effects.
  • Asp. Tox. 1: H304 - May be fatal if swallowed and enters airways.
  • Carc. 2: H351 - Suspected of causing cancer.
  • Flam. Liq. 2: H225 - Highly flammable liquid and vapour.
  • Skin Irrit. 2: H315 - Causes skin irritation.
  • Skin Sens. 1A: H317 - May cause an allergic skin reaction.
  • STOT SE 3: H336 - May cause drowsiness or dizziness.

Precautionary statements:

  • P201: Obtain special instructions before use.
  • P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
  • P241: Use explosion-proof equipment. P242: Use non-sparking tools.
  • P243: Take action to prevent static discharges. P261: Avoid breathing dust/fume/gas/mist/vapours/spray.
  • P273: Avoid release to the environment.
  • P280: Wear protective gloves/protective clothing/eye protection.
  • P301+P310: IF SWALLOWED: Immediately call a POISON CENTER/doctor.
  • P302+P352: IF ON SKIN: Wash with plenty of water.
  • P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
  • P308+P313: IF exposed or concerned: Get medical advice/attention.
  • P312: Call a POISON CENTER/doctor if you feel unwell.
  • P331: Do NOT induce vomiting. P333+P313: If skin irritation or rash occurs: Get medical advice/attention.
  • P362+P364: Take off contaminated clothing and wash it before reuse.
  • P370+P378: In case of fire: Use ABC powder extinguisher to extinguish.
  • P391: Collect spillage.
  • P403+P233: Store in a well-ventilated place. Keep container tightly closed.
  • P501: Dispose of contents/ container in accordance with local/regional/national/international regulation.
Truck cart
Delivery in 48 hours
+ -
Fast delivery within 48 hours from the order
Ship cart
FREE shipping over € 40
+ -
Free shipping if your order exceeds 40 €
Payment methods Payment methods
Support and phone orders
Do you need a quote for large quantities?
Ask for quote
Contact our offices
from Mon to Fri 08-13 // 14-18

The release agent creates a layer of wax on the surfaces of the mold / models, with a strong anti-stick action.

After drying, it creates a film that allows a simple extraction of the product or the mold. after each print it must be reapplied.

Applications: Apply the product inside the mold or matrix with a brush. Inside it is possible to pour the resin, both epoxy and polyurethane, and acrylic.

The first print requires at least three passes with 10-minute intervals; then one pass is enough before printing. The wax dries almost instantly; wait a few minutes for the solvent to evaporate and settle with a cotton cloth

Withstands high temperatures (up to + 180 ° C).

Directions for use: It is recommended in the preparation of molds and formworks in which to pour the resin and silicon rubbers

It is also possible to apply it on materials such as wood, metal, plastic and even cardboard, making in a few minutes the perfectly non-stick surface in which to pour the resin or other compounds.

Use a brush with soft bristles, apply a generous first coat as if it were a normal paint. let it dry completely and then apply a further coat to eliminate any pores or marks left by the bristles of the brush. let it dry and proceed with the application of the gelcoat. to remove the film in both cases of application use compressed air, if removal is difficult, use acetone

Warning: We do not recommend the use of devices that increase the temperature such as lighters, heat guns, etc.